Index >> Products >> Monitoring >> Poseidon xxxx
Poseidon 3268: WEB thermometer & I/O with SNMP
Ethernet temperature / humidity monitoring with 2 relay outputs and 4 dry contact inputs (Web, SNMP, and E-mail). Output relays can be controlled over the Web.
| Poseidon model 3268 can notice operator of crisis situation in various method (switched on/switched off contact, temperature or humidity out of set range).
When a Alarm occurs, the device sends you Email and notice Your NMS (Network Management Software) over SNMP.
Configuration and current values over graphic WWW interface.
- 2 relay outputs to control external devices
- 4 inputs to connect contact
- You can connect up to 4 temperature or humidity sensors.
- Typical use:
- Switch contact to send email or SNMP Trap to several recipients.
- Turn on external cooling fan and notify an operator after temperature gets out of preset range
|
|
Basis features
- Ethernet: RJ45 (10BASE-T)
- WEB: Embedded WEB server / GUI
- Sensors: 1xRJ11 1-Wire (max 4 temperature / humidity sensors)
- Inputs: 4 dry contact inputs (for detectors)
(Smoke, power, water leak, door contact, air flow, entry to the room)
- Outputs: 2 output relays (24 VDC)
(Air conditioning, server power supply, horn / light tower)
- M2M protocols: SNMP, XML
- Physical features: dimensions: 102 x 76 x 36 [mm]
- Response to thresholds: SNMP trap, E-mail
- Built-in functions: Output controlled with an input or sensor value ("Thermostat" mode).
- Support for programmers: HWg SDK
- Supported software
>> Poseidon model XXXX - overview of models
Application
>> Poseidon - application examples
>> Application study - Poseidon family
What Poseidon 3268 measures
 Sensors are connected over 1-Wire (RJ12), total wiring length must not exceed 10 meters. Each sensor monitors whether the value is in set range (including inputs for connecting contacts). It warns about set range exceeding (Alarm status) via Email or sending SNMP trap.
Compatible probes
- Temperature - Temp-1Wire (detailed photo)
Temperature probes, different lengths of connecting cables according to ordering number:
600 005 = 3 meters long, 600 242 = 1 meters long, 600 056 = 10 meters long)
- Humidity - Humid-1Wire (detailed photo)
Humidity probe, long:
600 279 = 3 meters long, 600 278 = 1 meters long)
- 4 inputs for Dry Contact
>> Value sensors
Topology
- WEB (HTML)
Values and state of sensors are presented on WWW page. The page is automatically reloaded every 5 second. There is a link to Flash Setup from main HTML page, update FirmWare and others
- XML
All sensor's values as well as alarm status information are available in XML files (temper.xml) and any application can log it from XML tags - more information
- SNMP
SNMP is protocol for monitoring of telecommunication devices, network infrastructure and related technology. The Poseidon is fully controllable over SNMP (v1, partially v2) - more information
- Modbus/TCP
Modbus/TCP is industrial standard for input from sensors and output to visualizing and SCADA systems. All values are available over Modbus/TCP - more information
- Alarms
- SNMP Traps
In case of exceeding "Safe Range" the sensor gets to Alarm status. To notify of this a SNMP Trap including alarm status description is sent to configured IP address - more information
- Email
In case of exceeding "Safe Range" the sensor gets to Alarm status. To notify of this a Email including alarm status description is sent to configured email address - more information
>> Poseidon –
communication protocols
HW interface
Overview of all sensors in our assortment: Sensors and accessories.
- Digital Outputs (Relay switch)
2 switching contacts of internal relay (output contact can be used as a NO (Normally Open) or NC(Normally Close))
- Digital Input (Dry Contact input)
4x input to connect contact (door for example) or output from relay (pins labled as NO or
NC)
- 1-Wire Bus - RJ11
A bus for use in IT, designed to connect temperature and humidity sensors over up to 10m
>> Interface for connecting sensors to Poseidon
Technical specification
- Port 1: Ethernet RJ 45 - 10BASE-T / 10 Mbit/s
- Port 2: SENSORS - 1-Wire bus (RJ12)
- Port 3: 4 Dry Contact input for contact connecting
- Port 4: 2 switching outputs of internal relay
- Power supply : 12V SS
- Device setting:
- Locally - RS-232 Setup
- UDP Config
- Over WEB - graphic Flash setup interface
- Over SNMP
| Port 1 - Ethernet port |
|
| + Interface |
RJ45 (10BASE-T) – 10 Mbit or 10/100 Mbit network
compatible |
| + Supported protocols |
IP: ARP, TCP/IP (HTTP, Modbus over TCP), UDP/IP (SNMP) |
| + SNMP compatibility |
Ver:1.00 compatible, some parts of the ver 2.0 implemented |
| |
| Port 2 - 1-Wire sensor bus |
|
| + Connector |
RJ12 (6 pins - 4 pins used only) |
| + Sensors / distance |
model 3265 - max. 5 sensors, up to 10 m total
model 3262 - max. 2 sensors, up to 10 m total |
| |
| Port 3 - Dry contact inputs |
|
| + 4 Contact inputs |
Connect it with a contact directly (dry contact). |
| + Isolation |
Galvanic isolated up to 50V DC |
| + Sensor type |
NO or NC contact switch |
| + Max distance |
Up to 30 m |
| |
| Port 4 - Relay switch outputs |
|
| + 2 Digital outputs |
Control via network (Web, XML, SNMP) or signal local alarm |
| + Isolation |
Relay switch up to 50V DC, max DC current 24V/1A, 50V/0.5A |
| + Switch type |
3 pins, can be used as NO or NC contact switch |
| |
| LED Status indicators |
| + POWER |
Green - power
OK |
| + LINK & Activity |
Yellow - Ethernet
connectivity |
| |
| DIP SWITCH configuration |
| + DIP1 - RS--232 Setup mode |
Not used |
| + DIP2 - Security |
ON = Security mode - remote configuration
disabled
OFF = Non-Security mode - remote configuration enabled |
| |
| Physical parameters |
|
| + Voltage requirements |
9 - 15V / 250 mA DC
coaxial power connector (barrel),
GND on the shield |
| + Dimensions |
102 x 76 x 36 [mm] |
| + Weight |
150 g |
Which software to use
- Configuration: UDP Config - IP address configuration
- Event processing: PD Trigger - reacts to events
- Monitoring and logging: HWg-PDMS - Monitoring software with MS Excel reporting
- Visualization: CapTemp - Process monitoring and control
- Other applications: Third-party SNMP software
- For programmers: HWg-SDK contains interface descriptions and examples of using M2M protocols in several programming languages
PD Trigger application example
With the PD Trigger application for Windows, it is possible to receive alarms (SNMP traps) from an unlimited number of Poseidon products and define conditions and actions based on the originating device and the probe name. For example:
- In case of air conditioning failure in server room A, send a SMS to Peter
- In case of alarm in server room B, send e-mail to Tom
- In case of electricity supply failure anywhere, send SMS to Peter and turn on a warning light at the receptionist's desk
>> Software for the Poseidon family
Sample ordering
- How long it takes to supply ordered samples?
We keep Poseidon 3268 units on stock and we supply samples them within 24 to 48 hours.We confirm time of delivery via email.
- What guarantee you offer?
Standard is 2 years, it can be extended after agreement..
- Where do I get price?
From our distributors, or by direct request the price (Email or Form).
- How to find out price of the Poseidon, sensors and accessories for my project?
Email us (see Contacts) or use Demand form. Fill in number of sensors, individual distance and what values exactly you intend to measure. Do not forget to mention what SW you will use for data processing or what you expect from the program. Tell use where you are from, we may recommend you installation company in your surroundings
- Can I pay by a payment card?
Yes but not online. Fill in the online order form, print it out. Write your payment card detail, sign it and fax it to our fax number. The other possibility is to pay via bank transfer.
- How do you supply the order?
We use several transport companies and FedEx for express shipments.
>> How to order product
>> Fill in Online order form
Order
| OID |
Type description |
600 254
|
Poseidon model 3268 (photo) |
600 255
|
Poseidon 3268 Tset (photo)
|
Accessories for Poseidon model 3268
 Power adapter
- Accessories for the 1-Wire bus (RJ12)
 Poseidon
T-Box [600
040]
Hub for up to 5 probes over 1-Wire bus (5x RJ12), connecting cable 0,1 meter long.
 Poseidon
T-Box2 [600
280]
Hub for up to 2 probes over 1-Wire bus (2x RJ12), connecting cable 3 meter long.
- Temp-1Wire (temperature probe)
- Humid-1Wire (humidity probe)
- Accessories for Inputs (Dry Contact)
- Door contact (photo) [600 119]
Magnetic sensor for door opening detection - small, easy to use..
- PowerEgg
Detection of external AC voltage (110 to 230V), configurable AC output(110 to 230V)
- Flood detector (water leak detection with autonomous sirene)
- Gas leak detector (Gas leak detection with autonomous sirene)
- Smoke detector (Smoke and fire detection with autonomous sirene)
- Motion detector
- Accessories for Output (internal relays)
- PowerEgg
Detection of external AC voltage (110 to 230V), configurable AC output(110 to 230V)
Keywords
rack mount environment monitoring, 19" rack temperature monitoring system, snmp environment monitoring,
19" rack environment monitoring, datacenter temperature, computer room temperature, snmp environment monitoring system,
e-mail alerts, sms alerts |
Similar and related products
|
Online demo
Configuration: 
Poseidon Family
