Supported accessories overview - All Supported accessories

Produktová řada HW group zahrnuje tři hlavní domény: Zařízení pro monitoring prostředí a technologických procesů, zařízení pro řízení a sběr dat systémů se sériovým rozhraním a vstupní systémy.

MBus

  • ABB DELTAmax (DHM13007)

    DELTAmax is a family of single-phase and three-phase electronic electricity meters for direct and indirect measurement. Thanks to the way their M-bus datagrams are designed, any M-bus product by ABB can be easily supported.
  • Advanced Power Meter APM 380

    Three-phase electronic electricity meter DEIF APM 380 for direct measurement to 80A
  • DBM23000

    Three-phase electronic electricity meter for indirect measurement
  • DHZ 5(x)/65 M-BUS (DHZ+)

    Three-phase electronic electricity meter for direct and indirect measurement up to 65A
  • DHZ 5/63-M-BUS

    Single-phase electronic electricity meter for direct measurement up to 63A
  • ED 310.(I).DB HWG

    Electricity meters ED310 are modern, electronic, programmable devices for monitoring consumption and supply of active electricity in the retail consumption area. During development and design, increased attention was paid to comply, with ample margin, with IEC, EN & DIN standards and communication protocol recommendations. ED310 is a poly-phase, electronic, four-tariff electricity meter of active energy of class A or B as per EN 50470-1 and 50470-3 designed for direct (ED310) and indirect (ED310.I) connection.
  • MGEIZ363, MGEIZ315

    Single-phase and three-phase electricity meters by EIZ - SCHRACK. Tested with the MGEIZ163-C model
  • PRO370D

    The PRO370D is a three phase kWh meter type with an LCD display in an exceptional small casing of 4 modules (76mm). This MID approved meter communi-cates via the German M-bus protocol as well as Far Infrared. More than 40 variables can be read out and the meter has secondary addressing, 2 tariffs and a programmable S0 output.
  • Saia Burgess ALD1D5FM

    Connect the single-phase ALD1 energy meters to the Saia PCD family of devices via an integrated S-Bus, M-Bus or Modbus interface in order to read relevant data such as energy, current, voltage and power (active and reactive). Pre-fabricated FBoxes are available to connect each type of meter. Depending on the interface type, the energy meters are also available in a one-way or two-way (bidirectional) design. The latter allow energy to be measured in both flow directions.
  • Saia Burgess ALE3D5FM

    Connect the three-phase ALE3 energy meters to the Saia PCD family of devices via an integrated S-Bus, M-Bus or Modbus interface in order to read relevant data such as energy, current, voltage and power (active and reactive). Pre-fabricated FBoxes are available to connect each type of meter. The energy meters are also available in a one-way or two-way (bidirectional) design. The latter allow energy to be measured in both flow directions.
  • sensonic® II calculator

    Converter to connect ISTA heat meters to M-BUS
  • MWZ 03

    Calorimetric counter for measuring heat and cold.
  • SCYLAR INT 8

    Energy calculator for universal use in systems for heating and cooling measuring.
  • Sensonic II

    Sensonic® is an electronic heat meter. The compact sensonic® II device and the sensonic® II flow sensor support flows of 0.6/1.5/2.5 m3/h.
  • SHARKY 775

    SHARKY ultrasonic compact energy meter can be used for measuring the energy consumption in heating / cooling application for billing purposes.
  • TECHEM S3

    Ultrasonic compact energy meter.
  • MULTICAL 21

    The MULTICAL® 21 / flowIQ® 21xx is a smart water meter based on the latest ultrasonic technology. The meter has no moving parts and maintains its pinpoint accuracy throughout its entire lifetime of up to 16 years.
  • CMa10 (THI)

    CMa10 is an indoor temperature and humidity sensor, which uses standard M-Bus communication. It is equipped with an easy-to-read display and has a message feature which can be used to present information to end-users. CMa10 can be used to enable comfort-level billing which means that residents pay for a specific predetermined temperature in their home.
  • M-count 2C

    Two-channel S0 pulse output converter to M-bus. The number of counted pulses is protected against power outage. Functionality is backed up with an internal, replaceable battery.
  • OA-4108

    Optical to M-bus converter for ABB electricity meters.
  • PadPuls M1

    The 1-channel pulse adaptor PadPuls M1 allows the use of meters with pulse output as M -Bus slaves. So for example, data from a simple water or electricity meter can central be read out by M-Bus.
  • PadPuls M2

    The 2-channel pulse adaptor PadPuls M2 allows the use of up to 2 meters with pulse output as M -Bus slaves. So for example, data from a simple water or electricity meter can central be read out by M-Bus. Optionally the user can activate a tariff function, by which energy or volume pulses can be accumulated in separate meter readings for primary and secondary tariffs.
  • DEIF MBus interface

    Converter from internal DEIF bus to the M-bus standard

RFID

  • Conteg DP-ZM-E2

    Ideální řešení pro Conteg rozvaděče, kde je zapotřebí samotná klika. Může být dodávána již nainstalována na rozvaděčích Conteg. Snadné připojení k řídící jednotce (RMS-ACS-U-RDU) pomocí přiloženého kabelu s barevně označeným konektorem RJ-45.
  • H3-EM-65-100

    Card Reader Type - HID® iCLASS, MIFARE® Classic, MIFARE® Plus, MIFARE® DESFire, HID 125kHz, EM 125kHz
  • H3-EM-67 (H3-EM-68)

    Card Reader Type - HID® iCLASS, MIFARE® Classic, MIFARE® Plus, MIFARE® DESFire, HID 125kHz, EM 125kHz
  • Conteg DP-ZM-E2

    Ideální řešení pro Conteg rozvaděče, kde je zapotřebí samotná klika. Může být dodávána již nainstalována na rozvaděčích Conteg. Snadné připojení k řídící jednotce (RMS-ACS-U-RDU) pomocí přiloženého kabelu s barevně označeným konektorem RJ-45.
  • H3-EM-65-100

    Card Reader Type - HID® iCLASS, MIFARE® Classic, MIFARE® Plus, MIFARE® DESFire, HID 125kHz, EM 125kHz
  • H3-EM-67 (H3-EM-68)

    Card Reader Type - HID® iCLASS, MIFARE® Classic, MIFARE® Plus, MIFARE® DESFire, HID 125kHz, EM 125kHz
  • HID® multiCLASS SE® RPxx

    Providing performance and reliability, HID's attractive, unobtrusive ThinLine II® proximity card reader is housed in a two-piece, weatherproof secure potted enclosure.
  • HID® Proximity ThinLine II

    Providing performance and reliability, HID's attractive, unobtrusive ThinLine II® proximity card reader is housed in a two-piece, weatherproof secure potted enclosure.
  • HWg-R3

    RFID reader in standard EM4100 (125kHz) with keyboard and interface of Wiegand.
  • JA-80H (JA-80N)

    The JA-80H keypad has an access card reader, a door bell button and illuminated keys. Controls door access and also operates the control panel. Cabled to a CP via a WJ-80 interface.
  • Rosslare AY-Q64

    The AY-Q64 has a slim rugged metal construction ideal for high traffic and harsh environments where PIN code and RFID card access are required. This model is epoxy filled, designed to withstand the rigors of the outdoor environment, and has advanced programming options as well as patented blue backlit keys. This elegant yet robust model can easily interface with Rosslare’s or most third-party controllers.
  • Universal RS-232 readers

    RS-232 is interface for carry information between two devices distance of up to 20 meters. The information is carry along patch wires higher voltage than is standard 5V for greater interference immunity. Data transfer is asynchronous with closely set transmission speed and synchronization by trailing edge start pulse.
  • Universal Wiegand readers

    Wiegand je standardní rozhraní, kterým komunikují čtečky bezkontaktních karet. Přesněji - komunikace je jednosměrná. Čtečka po sejmutí kódu vyšle v protokolu Wiegand kód a některé další údaje. Označení Wiegand je vždy doplněno ještě číslicí, která označuje typ protokolu. Mezi nejčastější patří protokoly Wiegand 26, 30, 32, 40 a 42.
  • Conteg DP-ZM-E2

    Ideální řešení pro Conteg rozvaděče, kde je zapotřebí samotná klika. Může být dodávána již nainstalována na rozvaděčích Conteg. Snadné připojení k řídící jednotce (RMS-ACS-U-RDU) pomocí přiloženého kabelu s barevně označeným konektorem RJ-45.
  • H3-EM-65-100

    Card Reader Type - HID® iCLASS, MIFARE® Classic, MIFARE® Plus, MIFARE® DESFire, HID 125kHz, EM 125kHz
  • H3-EM-67 (H3-EM-68)

    Card Reader Type - HID® iCLASS, MIFARE® Classic, MIFARE® Plus, MIFARE® DESFire, HID 125kHz, EM 125kHz
  • HID® multiCLASS SE® RPxx

    Providing performance and reliability, HID's attractive, unobtrusive ThinLine II® proximity card reader is housed in a two-piece, weatherproof secure potted enclosure.
  • Universal RS-232 readers

    RS-232 is interface for carry information between two devices distance of up to 20 meters. The information is carry along patch wires higher voltage than is standard 5V for greater interference immunity. Data transfer is asynchronous with closely set transmission speed and synchronization by trailing edge start pulse.
  • Universal Wiegand readers

    Wiegand je standardní rozhraní, kterým komunikují čtečky bezkontaktních karet. Přesněji - komunikace je jednosměrná. Čtečka po sejmutí kódu vyšle v protokolu Wiegand kód a některé další údaje. Označení Wiegand je vždy doplněno ještě číslicí, která označuje typ protokolu. Mezi nejčastější patří protokoly Wiegand 26, 30, 32, 40 a 42.

Handles

  • Conteg DP-ZM-Ex

    Ideální řešení pro Conteg rozvaděče, kde je zapotřebí samotná klika. Může být dodávána již nainstalována na rozvaděčích Conteg. Snadné připojení k řídící jednotce (RMS-ACS-U-RDU) pomocí přiloženého kabelu s barevně označeným konektorem RJ-45.
  • EM (EM-10-12-410) - E-Keeper Electronic Strike

    This "next-generation" access control solution provides the convenience of electronic access and push-to-close operation in one unit. Its low installed cost, compact design, and versatile installation options make it an easy, affordable solution for new or retrofit applications in a variety of enclosures – large and small.
  • EM-05 (EM-05-11-111) - Miniature Electronic Keeper System

    The compact version of Southco's electronic strike, the Miniature E-Keeper System delivers enhanced access control to applications that require concealed, controlled, secure access. Its versatility, ease of installation and slim design enable an easy transition from mechanical to electromechanical latching solutions.
  • H3-EM-67 (H3-EM-68)

    Card Reader Type - HID® iCLASS, MIFARE® Classic, MIFARE® Plus, MIFARE® DESFire, HID 125kHz, EM 125kHz
  • Southco H3-EM

    Electronic swing-handle from Southco for rack/cabinet access systems. Can be extended by HWg-SHe or HWg-SH4e for remote cabinet door access control. Supplied with a 4m connection cable.
  • Southco R4-EM - 8 Series

    The R4-EM 8 Series Electronic Rotary Latch Series combines the efficient and robust performance of a rotary latch mechanism with simplified DC motor actuation. The R4-EM 8 Series is available with an optional door sensor, integrated connector and mechanical override bracket. Flexible, concealed installation provides vandal-resistance and accommodates a variety of cabinet designs.
  • Southco R4-EM - 9 Series Electronic Rotary Latch

    Southco’s R4-EM 9 Series Electronic Rotary Latch delivers next generation electronic latching through microprocessor controlled actuation, providing highly intelligent, reliable electronic access. The internal microprocessor allows expanded intelligence with integrated door and lock status sensing for complete security monitoring. Lightweight extended housing offers increased tamper resistance, while an integrated connector and snap-on manual over-ride bracket simplify installation. Additionally, the 9 Series offers an optional open/close detent feature to prevent unintended door release.
  • Southco R4-EM 5 & 7 Series

    Southco’s R4-EM 5 & 7 Series Electronic Rotary Latch provides reliable electronic access control in demanding environments. With its corrosion-resistant plated-steel or stainless steel outer body construction and fully-sealed internal actuator, the Outdoor R4-EM provides reliable electronic locking that is resistant to moisture and dust.
  • Basic Electric Lock (E-lock BeFo 512)

    E-lock BeFo 512 is an electromagnetic lock suitable for the connection to our RFID constructions or coded locks.
  • Magnetic Lock with Signal Output (EM600S-Mag. Ctc)

    This high end lock has a 600lb (272Kg) holding force and includes a built-in Magnetic Contact for Door Status Monitoring (Open or Closed). Input voltage is user selectable for either 12 volts DC or 24 volts DC.